Yanhua Tech newly released Yanhua Module 35 to work with Mini ACDP1/ACDP2 for Toyota R7F714xx ODO/Buick BCM (NEC3558) mileage correction. The module using a quasi-blind plug-in interface board, No soldering, No need to pry up the chip pins, No capacitor removal, No soldering is required to read and write data without damage. The software comes with pin detection function, making data reading and writing safer and more reliable.
What can Yanhua ACDP Module 35 do?
It can perform the mileage correction function below.
- Support Toyota semi-LCD meter mileage correction with chip model R7F701441.
- Support Toyota full LCD meter mileage correction with chip model R7F701401.
- Support Buick BCM mileage correction with chip model NEC3558.
Which car models are supported by Yanhua ACDP Module 35?
Support Buick (17–22), Toyota (21–24) Levin, Corolla, Camry, RAV4, Frontlander, Sienna, Alphard, Vellfire and so on…
How to enter the menu?
Run ACDP APP
Select Module>> TOYOTA ODO>> R7F701401 or R7F701441>> Identify Info>> Pre-process chip>> Reset mileage (auto mode)
Or select Module>> Buick BCM (D70F3558)>> Identify>> Auto Mode
Note:
If you cannot find the Module function on the main menu, please go to setting to clear cache first.
How to connect Yanhua ACDP, Module 35 and Toyota/ Buick Cluster?
- For TOYOTA R7F701401
1.Push the interface plate latch to the unlock position, locate the motherboard chip and the latch fastening points, and determine the installation area of the interface plate.
2.Find the correct positioning holes of D1-D4 on the instrument.
3.Check the Test Point Pin Definition (RXD, VCD, VRCG1, GND3, VRCG0, FLMD, TXD, RES)
4.Place the interface board accurately into the installation area, align the pins with the D1, D2 positioning holes.
5.Press down on the interface board, push the PCB lock buckle to the Locked position to lock the interface board, installation is done.
- For TOYOTA R7F701441
1.First, complete the installation of the 1A interface plate, then proceed to install the 1B interface plate.
2.Find the interface board installation area on the instrument according to the visual positioning mark on the interface board.
3.Locate the D1, D2 and D4 positioning holes correctly on the instrument panel.
4.Accurately place the interface board into the installation area, align the D2 and D4 positioning points and screw hole.
5.Check the R7F701441- TOYOTA-1A Test Point Pin Definition (VRCG0, VRCG1, GND2, VCC, FLMD, RXD and RES).
6.Clamp the interface board and the odometer by hand, and tighten the copper column.
7.Locate the D1, D2 and D4 positioning holes correctly on the instrument panel.
8.Locate the D1, D2 positioning holes correctly on the instrument panel.
- Check the R7F701441- TOYOTA-1B Test Point Pin Definition (TXD)
10.Align the screw fastening hole, TXD1 connection pin, and D1 positioning points, then press down on the interface board and tighten the copper pillars.
- For Buick BCM (NEC3558)/D70F3558
1.Based on the probe of the interface board, determine the installation area of the interface board on the instrument
2.Find the correct positioning holes of D1, D2 on the instrument
3.Check the Test Point Pin Definition (RTXD, RES, GND, T, FLMD, VCC)
4.Align the interface board probe with the probe hole on the odometer board and with the D1 and D2 positioning points
5.Clamp the interface board and the odometer board by hand, with the TOP of the buckle facing upwards, and insert the buckle into the Lock mark on the interface board to lock the interface board.
Yanhua ACDP Module 35 for Toyota R7F714xx ODO/Buick BCM (NEC3558) Mileage Correction will be in stock next Friday. You can pre-order it now! First come, first serve!
https://www.obdexpress.co.uk/wholesale/yanhua-acdp-module35-for-toyota-buick-mileage-correction.html
No comments:
Post a Comment