Solved miss synchronization data file when AKL Programming

 One customer gave the feedback that he failed to use Xhorse VVDI Key Tool Plus to generate a key for VW Polo 2016 MQB all key lost after online calculation and successful immo data saving.

 

Possible reasons:

Miss synchronization data file.

Actually, the prompts before generating the dealer key have answered why.

 

For MQB instrument immo system, it needs token cost and:

1)Add Key needs a working key

2)All Key Lost needs the synchronization data

Although he’d done online calculation (cost 1 token each time) to get immo data, he still lacked synchronization data.

 

Solutions:

Go contact a third party like your vehicle’s dealer or specific online servers etc. Pay them extra to get synchronization data but part of vehicles not supported.

Load synchronization data to generate a dealer key.

Then press “Decode key” to finish following procedures as prompts and it should work.

 

Tips:

One can get the synchronization data only from a working key or a third party.

So always save the synchronization file when adding a spare key against unexpected needs.

 

Done!

VVDI Key Tool Plus - Benz W211 AKL programming

 This is the test on how we use Xhorse EZS Adapter and VVDI Prog to read EZS EEPROM data and use Xhorse VVDI Key Tool Plus to get the password and program a new BE key for Mercedes Benz C240 2004.

Tools:

Xhorse VVDI Key Tool Plus

Xhorse EZS Adapter for Chassis W211

Xhorse VVDI PROG

Benz W211 EZS

Part 1. Read original&flashed EEPROM data

Put EZS in Xhorse EZS adapter for W211.

Use the EZS Adapter Cable to connect Xhorse VVDI Prog and EZS adapter.

Supply 12V power for Xhorse VVDI Prog.

Open VVDI Prog software.

Press “Read” to read the EEPROM.

Press “Verify” to check the information.

Then press “Save” to save the EEPROM data file.

Press “Flash” to flash the EEPROM.

Press “Verify” to check the information.

Then press “Save” to save the flashed EEPROM data file.

Upload both files to Xhorse VVDI Key Tool Plus.

Part 2. Get the password and prepare key file

Time to use Xhorse VVDI Key Tool Plus.

Press

IMMO Programming>>Europe>>Benz>>Select from system>>Prepare Key File>>Start programming>>Prepare Key File>>OK

Load the Original EEPROM file and we will see the password.

Press “OK” to input the password.

Here choose v051.

Insert a new key into Xhorse VVDI Key Tool Plus and press “OK”.

Then save the key file.

Part 3. Write a new BE key

Back to “Select from system”. Press

Read/Write key via IR>>Start programming

Press “Infrared identification key information” to check the key information.

Press “Continue” to get back and press “Erase the BE key”.

Also we can press “Infrared identification key information” to check the key information.

Press “Write BE key” and load the key file to be written.

Writing data success.

Press “Infrared identification key information” to check the written key information.

Restore EZS to the vehicle and start it by the new key.

Complete!Nice work!

This is how we use Xhorse EZS Adapter, VVDI Prog and VVDI Key Tool Plus for Benz Chassis W211.

VVDI Mini Key Tool errors and solutions

 This is a collection about common errors and corresponding solutions during the use of Xhorse VVDI Mini Key Tool.

 

1.“SAFE2”“USB---PC” error

Issue description:

Xhorse VVDI Mini Key Tool stuck on the upgrading for 6 hours with nothing on the screen but “SAFE2” or “USB---PC” prompts.

 

Solution:

Update firmware on the Upgrade Kit

1)Connect the device to a computer via USB cable

2)Start the Upgrade Kit, and then select “Mini-Keytool(KeyLark)” and press “Find Device”

3)Press “Upgrade” and wait until Upgrade completed

 

2.The storage space of reward point is full, please synchronize

Issue description:

Try to generate remote by Xhorse VVDI Mini Key Tool, but it says storage full. How to synchronize or delete it?

 

Solution:

A firmware update on the Xhorse Upgrade Kit will solve this problem.

1)Update firmware as above

2)Update database by the connection of Xhorse app via Bluetooth

 

3.error code: Error:9B

Issue description:

Fail to generate Toyota XM series key by Xhorse VVDI Mini Key Tool. It shows the error, what’s the problem?

 

Solution:

Change other keys to program.

The key used may be a Chinese version one, so it cannot be used with an overseas device.

 

4.Fail to generate

Issue description:

Use Xhorse VVDI Mini Key Tool to generate a remote as the prompt but failed.

Solution:

Change the position of wireless smart remote because the sensing area may not be able to recognize the chip with weak signal.

 

5.Always asks to update

Issue description:

Always asks to update when using Xhorse VVDI Mini Key Tool. After successful update, it will prompt me to update as well.

 

Solution:

1)Reinstall Xhorse app

2)Install and login in on other phones. No need for extra fees in the same account.

 

6.Cannot read immo data

Issue description:

Have tried many keys, still cannot read immo data by Xhorse VVDI Mini Key Tool.

 

Solution:

Select “Special Function” and then try “Key Charge”. Keep operating for about one minute and then go to read immo data. The key’s frequency should be recognized.

Done!Simple and nice.

 

https://www.xhorsestore.co.uk/

How to solve Xentry EWA not working and unable to connect to Wifi?

Problem:

I purchased MB SD C4 Plus and the latest software V2021.03, I was sent a replacement HDD due to Windows forced update. I installed the new HDD on the original laptop and 2 of my own personal laptops. It isn't working properly.

 

I asked for Windows 10 Pro to be loaded, so I can change updates behavior in group policy to stop forced updates. None of the programs (Xentry, EWA) are working and I am unable to connect to WiFi. The system does not recognize ANY networks I know are available. The Windows software isn't activated either and I don't know if that is causing problems. And if I try to enter group policies on the machine I am told I don't have authorization.

 

 

obdexpress.co.uk Solution:

1. The software needs to be activated, there is a pdf description on the desktop after your computer is started, you can send me the id according to the description to activate
2. If your computer can't connect to the wifi network, means the wlan network card driver is not installed, please install Wlan Network card driver (I used the driver genius to repair the computer driver)

http://www.drivergenius.com/ ), you can download this to try, or you can find a computer driver repair tool commonly used in your country.

Question:

The HDD is in my HP G60 currently, as Spencer recommended, not the ThinkPad that was sent with the multiplexer and cables. Does it need to go back into the ThinkPad?

 

Answer:

If there is no problem with the Thinkpad computer, you can go it back. If you want to use it on your own computer, you need to reactivate the software.

 

Question:

Ok. I'd like to use mine if it doesn't matter. I don't understand what you meant about the network driver. I apologize I'm literate but not proficient with computers.

 

Answer:

You just said that your computer cannot connect to a wifi network, so I think your computer should not have the wlan network card driver installed, you need to repair the network card driver.

Hope it helps!

 

Any problem with MB SD C4 Plus Xentry EWA software activation, Wifi connection, please feel free contact at www.obdexpress.co.uk.

VVDI Key Tool Plus unlock smart key with Key Renew Adapter Guide

 This is a test on how we use Xhorse Key Tool Plus&Key Renew Adapter to unlock smart key without soldering necessary. Apart from Key Tool Plus, key renew adapters are also compatible with other VVDI Key Tools (Key Tool, Key Tool Mini and Key Tool Max). Beside, key renew adapters are only for OEM circuit board, meaning the adapters do not work on aftermarket smart keys.

 

1. Check on Xhorse app if there is an adapter available for your key

Open Xhorse app on your phone, then select

Special Function>>Remote Renew>>NISSAN>>AES SmartKey-A2C32801600-E124BTN 433MHz

Here it will show you if there is an available adapter. If not, the connection diagram below also shows you how to renew the key with Soldering Cable, including where we need to solder, on which wire we have the black/red/yellow/brown wire...

(More details about Soldering Cable: https://www.xhorsestore.co.uk/upload/pro/21060416227999535711.pdf)

 

 

2. Unlock smart key by VVDI Key Tool Plus

Here we will show you two examples: Nissan Smart Key & Dodge Smart Key. And we are going to unlock the two keys in two different ways. For Nissan, unlock key first and then read transponder; for Dodge, read transponder first, unlock key and read transponder again.

 

• Unlock Nissan Smart Key

Have Nissan key’s circuit board in the adapter and use the cable to connect the adapter to Key Tool Plus.

 

Select

Special Function>>Remote Renew>>NISSAN>>AES SmartKey-A2C32801600-E124BTN 433MHz>>Unlock, and wait...

Unlocked successfully!

 

Take the key out and put it in the coil.

 

Back to Homepage, select

Transponder Clone>>Read Transponder，

here we can see we successfully unlocked it.

 

• Unlock Dodge Smart Key

Put the key in the coil first. Select

Transponder Clone>>Read Transponder,

here we can see this used key is “already locked”.

 

Put it back to its adapter and connect the adapter to Key Tool Plus.

Back to Homepage, and select

Special Function>>Remote Renew>>Chrysler&Jeep&Dodge>>M3M Hitag2>>Unlock, and wait...

Back to Homepage and turn to Read Transponder interface as before.

Here we can see the key turns “Unlocked”.

 

Done!

Well, this is the correct way to unlock smart key without soldering by VVDI Key Tool Plus&Key Renew Adapter.

Can Kess V2 KTAG and PCMflash test with USB 3.0?

 Question:

if USB 3.0 is tested with all the diagnostic and remap tools i.e Kess/KTAG and PCMflash? because the notebook I would get has only 3x USB 3.0 (the blue connector). Till now I had only the classic USB 2.0.

 

Answer:

Yes they will work.

No matter ori & clone Kess /KTAG and PCMflash. it will work for you. I tested Kess/KTAG by myself, and works without any problems. You have nothing to fear.

 

And PCM with Scanmatik2 work well with USB3.0.

Autel IM508 + XP400 key programming for Fiat punto evo 2010

 What key programmer for Fiat punto evo 2010 car to prepare key with remote?

 

Just few of your possibilities:

if you choose the "bsi take out then read eeprom dump" way:
-Tmpro
-Miraclone
-Avdi
- By hand with any Hitag2 programmer if you know the delphi remote page data
- Zedfull

If you choose the "read the EEPROM thru obd" way
for dumping
- Avdi
- truecode
- ioterminal
- Autel IM508 +XP400 Pro or Autel IM608 + XP400
- Zedfull
for precoding:
- Avdi
- Tmpro2
- Autel
-Zedfull

If you choose the straight obd way:
- Avdi
- Autel
- Zedfull
- SP pro
- MVP

And plenty other stuff like SMOK..etc

 

Here, I prefer to Autel IM508 +XP400 Pro. Look at the following table, it covers Fiat punto evo 2010 and do add key, all keys lost, read password.

 

To be updating...

 

www.obdexpress.co.uk

2M2 Tank Key Cutting Machine Update APP 2.2.8

 2M2 Tank Car Key Cutting Machine Update:

New APP: 2.2.8

Key data version: 809

Current version: 2021051801

Updating contents:

1- Renault single side key

2- VA2 1049 data and guiding picture

3- VA6 key data 66

4- Mitsubishi key data bug

5- Universal key duplicate

6- Cutting speed adjusted

7- HON66, SIP22,GT15,HU83,NE66,HU64,HU162T improved

 

If you are interested in 2M2 Tank Car Key Cutting Machine, visit https://www.obdexpress.co.uk/ for more details.

ID48 key programming - VVDI Key Tool

 VVDI Key Tool transponder clone ID48: 746DA4EC, it says "This ID48 can copy by keytool offline, but it has risking of broken original key, suggest using ID48-96bit copy online...".

 

How to do?

vvdi key tool is no longer supported by xhorse. The new ones are mini key tool, key tool max and key tool plus.

All u do is read the id48 chip, then select clone, then follow the prompts, it may or may not make u sniff the ignition, just follow the onscreen prompts.

Yes, id48 copy/clone cost each time. U can either use your bonus points (150 in total) or u can buy id48 credits for about $8 each. U get bonus points for every remote that u generate with a xhorse machine.